Matte transparant gekleurde houtbescherming/beits op basis van
een solventgedragen alkyd emulsie voor buiten.
De belangrijkste eigenschappen zijn:
– Houtstructuur blijft zichtbaar en wordt, afhankelijk van de houtsoort, geaccentueerd.
– Vochtregulerend.
– Bestand tegen UV-stralen.
– Optimaal kleurend effect.
– Eenvoudig te onderhouden
Het is bestemd voor het verfraaien en beschermen van schrijnwerk, uitermate geschikt voor naaldhout.
Als één-pot systeem op niet-maatvaste constructies, zoals : tuinhuisjes, gevelbekleding, houten
tuinafsluiting, enz…
Als primer in een transparant systeem op maatvaste constructies in loofhout
Specs
Kenmerken
Productvorm: Kant-en-klaar gemengd
Geschikt voor gebruik binnen: Nee
Geschikt voor buitengebruik: Ja
Beste gebruik: Hout
Type finish: Semi-glans
Volume: 2,5 l
Kleurnaam: Light Oak
Samenstelling: Op basis van oplosmiddelen
Oppervlakterendement (min): 7 m²/L
Oppervlakterendement (max): 14 m²/L
Matheid: Transparant
Aantal lagen (min): 1
Aantal lagen (max): 3
Aantal verfbeurten, noot: Finishing coat - new /bare large surface areas - 3 coats; Maintenance - 1 coats unless surfaces are excessively weathered; Base stain - new/bare timber - 1 coat prior to Cetol Filter 7 Plus or Cetol THB Plus
Aanbevolen laagdikte (droog): 10 µm
Minimale droogtijd: 4 uur
Maximale droogtijd: 6 uur
Overschilderbaar na (min): 18 uur
Overschilderbaar na (max): 24 uur
Inhoud vluchtige organische stoffen (VOS): 400 g/l
Inhoudetiketteringsysteem voor vluchtige organische stoffen (VOS): Hoog (25 - 50%)
Gereedschap reinigen: Clean brushes and equipment with brush cleaner immediately after use. If spilled, Cetol HLS plus may be removed immediately while still wet, using white spirit
Gebruiksinstructie: Conditions : Do not apply if there is a risk of rain, or when air/substrate temperatures are below 5ºC or above 30ºC during application or drying periods. Protect from frost and rain until dry.Failure to meet these requirements may adversely affect the drying, visual quality and durability of the finish.Initial Procedure Ensure product is thoroughly stirred before and during application, otherwise sheen and colour variations may be experienced. Cetol HLS plus is supplied ready for use. Do not thin.Applying the product For best results use a good quality, long-haired, soft bristle brush. On new work, where practical, the initial coat should be applied all round prior to fixing. P ay special attention to any areas of exposed end grain, tops and bottoms of doors, and undersides of cills.The product should be applied in a full flowing coat (working well into joints, and ensuring end grains or sawn timbers are saturated with product). Excess surface material should be re-distributed after 5-20 minutes (depending on conditions), using a dry brush (which should be periodically dried with a lint-free cloth) and the minimum number of strokes required to produce an even overall colour. This ensures that the first coat satisfies the porosity/absorption of the timber. Allow a minimum of 18-24 hours drying time. Where appropriate (e.g. for joinery items such as windows and doors), the first coat should be carefully denibbed using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper, in the direction of the grain. Do not break through the surface coating. Remove all dust.Cetol HLS plus should be applied in a full flowing manner in the direction of the grain, using the minimum number of brush strokes necessary to produce an acceptable finish. Avoid overbrushing, as this will reduce the protection afforded.Subsequent coatings should be applied as soon as possible after the previous coat has dried, but no sooner than 12-24 hours, in order to provide full protection. In any event this period should not extend beyond three months, otherwise additional preparation and coats may be necessary. If applied to exterior timber and the contract is of long duration, it is suggested that a further coat be applied prior to handover to make good any weathering during the construction period
Hoe te bewaren: Store in cool, dry, frost-free conditions
Oppervlaktevoorbereiding: General: Ensure the timber surface is suitably prepared, clean and dry, with dust, dirt, wax atnd grease removed and allowed to acclimatise to its end-use environment. The moisture content should not exceed 18% prior to coating.Degrease any exposed bare timber surface by wiping with a cloth dampened in a suitable solvent. Certain timber species contain high levels of natural wood extractives or exudates and some softwood can be highly resinous. Resinous deposits should be removed with a scraper. Any remaining residues should be removed using a lint-free cloth dampened with a suitable solvent, frequently changing the face of the cloth. Allow solvent to evaporate fully before overcoating. The use of both eye and hand protection is strongly advised. We do not recommend the use of “knotting agents” with translucent finishes as they are not always fully effective in “sealing in” resin,the presence of knots is often highlighted and adhesion of coatings can be impaired.When filling, be sure to use fillers specifically designed for use with timber. General or all purpose fillers are not suitable, particularly on external areas, as they cannot cope with timber movement and work loose. New timber: Where a superficial application of preservative to softwood and hardwood is deemed necessary, such as timbers in Durability Class 3 or lower, use Cuprinol Wood Preserver Clear (BP). For Class 4 (in ground contact) and 5 (marine), use pre-treated wood specific for these conditions. Preservative pre-treatments must be fully dry before the application of Cetol HLS plus. Do not use on substrates which have had water-repellent preservative pre-treatments applied. Where possible, the first coat should be applied all round prior to fixing. Only use non-ferrous screws, nails and fixings.Base stained / Primed : Denib using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper, in the direction of the grain. Do not break through the surface coating. Remove all dust. To ensure optimum durability and uniformity of appearance, we recommend the use of a coat of Cetol HLS plus prior to finishing. Note: Where there is localised damage, or deterioration has occurred as a result of exposure of the factory coating for longer than 3 months, affected areas should be thoroughly sanded back to a sound substrate. All damaged or decayed timber must be removed and replaced, cutting at least 25mm into sound timber. When splicing in new sections of timber, consideration should be given to the use of a timber species whose natural durability is sufficient. Brush apply two coats of Cuprinol Wood Preserver Clear (BP) to saturation. Ensure timbers are thoroughly treated, especially any end grain sections, and are fully dry before splicing in. Secure with non-ferrous fixings and fill all voids surrounding the spliced-in area with a suitable repair compound such as Dry-Flex from Repair Care
Verpakking
Breedte verpakking: 188 mm
Diepte verpakking: 170 mm
Hoogte verpakking: 157 mm
Cetol HLS plus 2,5l lichte eik
Matte transparant gekleurde houtbescherming/beits op basis van<br />een solventgedragen alkyd emulsie voor buiten.<br />De belangrijkste eigenschappen zijn:<br />– Houtstructuur blijft zichtbaar en wordt, afhankelijk van de houtsoort, geaccentueerd.<br />– Vochtregulerend.<br />– Bestand tegen UV-stralen.<br />– Optimaal kleurend effect.<br />– Eenvoudig te onderhouden<br />Het is bestemd voor het verfraaien en beschermen van schrijnwerk, uitermate geschikt voor naaldhout.<br />Als één-pot systeem op niet-maatvaste constructies, zoals : tuinhuisjes, gevelbekleding, houten<br />tuinafsluiting, enz…<br />Als primer in een transparant systeem op maatvaste constructies in loofhout
